How to use the manual settings on the remote control of the Osaki OS 3d pro dreamer massage chair? Every chair has automated pre-programmed settings where you push a button and it puts you into program like morning or night or muscle relief or stretch but every chair also has manual settings, so you can move the rollers where you want them to go do what you want them to do at the speed that you wanted to do it and you can employ airbags, any airbags that you want may be just the arms maybe just the legs.
All of the chairs have that customization capability and the Dreamers were no different. I'm going to show you briefly how you access this on the remote control so we're going to zoom in on the remote on the bottom of the dreamer remote and by the way, this also applies to the Osaki 7200 and in the sea is the Osaki 1700 h they all have the same remote control the difference with this one is that you have the 3d settings there and we're not going to go into that today but at the bottom of the remote is this latch it when you pull that little flap back you will see these various and sundry caricatures and these represent the different modes like kneading and tapping kneading and pummeling you know it tell in shiatsu it tells you the different things you can do so what you do first of all is you select what you want the chair to do for you in the area that we're going to have it work so let's pick needing oh actually, of course, you want to turn the chair on and I'm going to move over to the site so we can so we can see this now let's say we want to have kneading and I'm going to return on the kneading and you're going to see the rollers here are needing so they're going to move up and down the spine but we want it to stay in a particular place and we're going to call it point 10 point location you can either do a zone or it'll stay in one place and move six inches up or down or you can push point where it stays in one place right now it seems to be going up and down in a zone well what I'm going to do and you can see on the remote here that arrow shows you where the rollers are going up down up down based on the zone that you've got it in but what we're going to do is we're going to push point and as soon as I push the point button you'll see that on the remote instead of arrows you've got a point and we'll see that the kneading is working right now here on about the upper upper shoulders maybe we want to move that down to the low back so let's move so you go up here to the shoulder position or the the position of where the rollers are and we're going to push the down button and now we're going to see the rollers go down see now they're going down down down let's say we want it in the low back so there we've got it a low back right there so manually we've moved there and now we can use the 3d and I lied earlier we are going to use the 3d if we want to move those rollers forward more you can see the setting on the remote control we're moving it all the way up to the top of the CD set 3d settings now you can really see the rollers kicking out you see that so you can move those rollers quite a bit more intensely forward then you then they go by default or we can retract them and move it back by going under the the minus sign on the 3d and we're going to pull those rollers back if it's too intense or you want something a lot lighter and you'll see here as I push it it goes back to a low low low setting and the person is using it will not feel it nearly as much as did before now you can hardly even see it moving if I push it again watch the roller zero as I push it forward you will see those rollers moving even more and more forward so now we've got the 3d setting all the way forward now what else you could do when you're in this position you can adjust adjust the speed of the roller so let's say we want to well let's not do that right now let's go over here to the stu the airbag let's say you want to select an airbag I'm going to turn on the let's let's turn on the shoulder airbags so now we can add the shoulder airbag and you can see these airbags here are starting to inflate you can see them inflating there and let's say we want to add also the hand airbags so down here we will see the hand airbags begin to inflate see that so I can manually set that so we've manually set the roller to the low back we've manually turned on the shoulder airbags and we've manually on the arm airbags and now why don't we go ahead and turn on the foot rollers I can turn that on as well and if you look down here you'll see the foot rollers moving so that is the manual setting of do using the manual settings of the Osaki OS 3d pro dreamer massage chair now let's say I want to increase the speed and I can't well I don't have it on the right if you if you change the mode to a tapping the speed will not change you cannot change the speed of needing you have to move it to tapping which I've done and then you can see here on the remote the speed graph and I'm going to turn that up and then you can increase the speed that will somewhat increase intensity as well now it's back down but if you watch the rollers I'm going to increase the speed and you'll see it start to shake even more you see that now it's shaking like crazy that's the speed of the tapping is much faster so you can adjust you can adjust the intensity of the rollers by moving them forward or back like I showed you or you can adjust the speed to make the tapping or the or the pummeling even quicker and that's another way to increase the intensity but that and then, of course, you can adjust the airbag intensity you see the up here in the remote it says intensity you can push the button to increase the intensity of the airbags so it increases the squeeze of the airbags and also you can adjust the width of the rollers to make them wider or narrower if you're a big bodied person you might have a wider vertebra on the spine you want to move those rollers out a little bit because it might be uncomfortable to have the rollers hitting your bone or if you're thin you can move those rollers in and you can do that with the width feature so those are the manual settings of the Osaki OS 3d pro dreamer I hope it made sense we kind of jumped around from one place to the other on the remote control but it's very easy to use and this principle applies to all chairs that have manual settings you select what you want the rollers to do then you move the rollers where you want them to work then you determine if you want it to be a point or a zone area that you want massage and then you can increase the intensity of the rollers either by speed and or the forward motion of the rollers the 3d year older intensity and then you can select whatever airbags you want foot rollers any other features you can kind of add it on peace me I'll a card if you will so you're customizing this room is massage just for you but that is the manual settings for the Osaki os3 pro dreamer I hope you found the video helpful if you did feel free to share us on Facebook Twitter Linkedin Google+ and of course like us and that will help you help us spread the word about massage chairs again I'm dr. Alan white here for massage chair relief calm and we will see you on the next video bye
0 Response to "Manual Settings - Osaki OS-3D Pro Dreamer Massage Chair (Video Tutorial)"
Post a Comment